1) The modulation
technique used for mobile communication systems during world war II was
a. Amplitude modulation
b. Frequency modulation
c. ASK
d. FSK
ANSWER: Frequency modulation
2) ———– introduced
Frequency Modulation for mobile communication systems in 1935.
a. Edwin Armstrong
b. Albert Einstein
c. Galileo Galilei
d. David Bohm
ANSWER: Edwin Armstrong
3) The early FM
push-to-talk telephone systems were used in
a. Simplex mode
b. Half duplex mode
c. Full duplex mode
d. None of the above
ANSWER: Half duplex mode
4) DECT stands for
a. Digital European Cellular Telex
b. Digitized Emergency Cellular Telephone
c. Digital European Cordless Telephone
d. Digital European Cellular Telephone
ANSWER: Digital European Cordless
Telephone
5) World’s first cellular
system was developed by
a. Nippon Telephone and Telegraph
(NTT)
b. Bellcore and Motorola
c. AT&T Bell Laboratories
d. Qualcomm
ANSWER: Nippon Telephone and Telegraph
(NTT)
6) Paging systems were
based on
a. Simplex systems
b. Half duplex systems
c. Full duplex systems
d. None of the above
ANSWER: Simplex systems
7) Paging systems could
be used to
a. Send numeric messages
b. Send alphanumeric messages
c. Voice message
d. All of the above
ANSWER: All of the above
8) Garage door opener is
a
a. Transmitter
b. Receiver
c. Transceiver
d. None of the above
ANSWER: Transmitter
9) Carrier frequency of a
TV remote control is in the range
a. of Infra red
b. < 100 MHz
c. < 1 GHz
d. < 2 GHz
ANSWER: of Infra red
10) Half duplex system
for communication has
a. Communication in single direction
b. Communication in single direction at a time
c. Communication in both directions at the same
time
d. None of the above
ANSWER: Communication in single direction
at a time
11) MIN stands for
a. Mobile Identification Number
b. Mobile Internet
c. Mobility In Network
d. None of the above
ANSWER: Mobile Identification Number
12) The process of
transferring a mobile station from one base station to another is
a. MSC
b. Roamer
c. Hand off
d. Forward channel
ANSWER: Hand off
13) PCN is
a. Wireless concept of making calls
b. For receiving calls
c. Irrespective of the location of the user
d. All of the above
ANSWER: All of the above
14) IMT-2000 is a digital
mobile system that functions as
a. Pager
b. Cordless
c. Low earth orbit satellites
d. All of the above
ANSWER: All of the above
15) The 2G cellular
network uses
a. TDMA/FDD
b. CDMA/FDD
c. Digital modulation formats
d. All of the above
ANSWER: All of the above
16) NADC is a 2G standard
for
a. TDMA
b. CDMA
c. Both a & b
d. None of the above
ANSWER: TDMA
17) 2G CDMA standard –
cdma one supports up to
a. 8 users
b. 64 users
c. 32 users
d. 116 users
ANSWER: 64 users
18) 2G standards support
a. Limited internet browsing
b. Short Messaging Service
c. Both a & b
d. None of the above
ANSWER: Both a & b
19) The 2G GSM technology
uses a carrier separation of
a. 1.25 MHz
b. 200 KHz
c. 30 KHz
d. 300 KHz
ANSWER: 200 KHz
20) 3G W-CDMA is also
known as
a. UMTS
b. DECT
c. DCS-1800
d. ETACS
ANSWER: UMTS
21) Commonly used mode
for 3G networks is
a. TDMA
b. FDMA
c. TDD
d. FDD
ANSWER: FDD
22) The minimum spectrum
allocation required for W-CDMA is
a. 5MHz
b. 2MHz
c. 500KHz
d. 100KHz
ANSWER: 5MHz
23) CDMA2000 1xEV
provides high speed data access with channel allocation of
a. 5 MHz
b. 50 MHz
c. 1.25 MHz
d. 4 MHz
ANSWER: 1.25 MHz
24) In TD-SDMA, there is
a frame of _____milliseconds and the frame is divided into _____ time slots.
a. 5, 7
b. 7, 5
c. 2, 5
d. 5, 2
ANSWER: 5, 7
25) The interference
between the neighboring base stations is avoided by
a. Assigning different group of
channels
b. Using transmitters with different power level
c. Using different antennas
d. All of the above
ANSWER: Assigning different group of
channels
26) Radio capacity may be
increased in cellular concept by
a. Increase in radio spectrum
b. Increasing the number of base stations &
reusing the channels
c. Both a & b
d. None of the above
ANSWER: Increasing the number of base
stations & reusing the channels
27) The shape of the
cellular region for maximum radio coverage is
a. Circular
b. Square
c. Oval
d. Hexagon
ANSWER: Hexagon
28) Hexagon shape is used
for radio coverage for a cell because
a. It uses the maximum area for
coverage
b. Fewer number of cells are required
c. It approximates circular radiation pattern
d. All of the above
ANSWER: All of the above
29) Centre excited
hexagonal cells use
a. Sectored directional antennas
b. Omni directional antennas
c. Yagi uda antennas
d. None of the above
ANSWER: Omni directional antennas
30) Spectrum Efficiency
of a cellular network is
a. The traffic carried by whole
network
b. The traffic carried per cell divided by the
bandwidth of the system and the area of a cell
c. Expressed in Erlang /MHz /km2
d. Both b and c
e. Both a and c
ANSWER: Both b and c
31) The advantage of
using frequency reuse is
a. Increased capacity
b. Limited spectrum is required
c. Same spectrum may be allocated to other network
d. All of the above
ANSWER: All of the above
32) The strategies
acquired for channel assignment are
a. Fixed
b. Dynamic
c. Regular
d. Both a and b
e. Both b and c
ANSWER: Both a and b
33) In a fixed channel
assignment strategy, if all the assigned channels are occupied, the call
a. Gets transferred to another cell
b. Gets blocked
c. Is kept on waiting
d. All of the above
ANSWER: Gets blocked
34) In a fixed channel
assignment strategy
a. Each cell is assigned a
predetermined set of frequencies
b. The call is served by unused channels of the
cell
c. The call gets blocked if all the channels of
the cell are occupied
d. All of the above
ANSWER: All of the above
35) In a dynamic channel
assignment strategy,
a. Voice channels are not permanently
assigned
b. The serving base station requests for a channel
from MSC
c. MSC allocates the channel according to the
predetermined algorithm
d. All of the above
ANSWER: All of the above
36) Advantage of using
Dynamic channel assignment is
a. Blocking is reduced
b. Capacity of the system is increased
c. Both a & b
d. None of the above
ANSWER: Both a & b
37) Disadvantage of using
Dynamic channel assignment is
a. More storage required
b. Calculations and analysis is increased
c. Both a & b
d. None of the above
ANSWER: Both a & b
38) In Dynamic channel
assignment, any channel which is being used in one cell can be reassigned
simultaneously to another cell in the system at a reasonable distance.
a. True
b. False
ANSWER: True
39) In Handoff
a. Process of transferring the call
to the new base station
b. Transfers the call
c. New channel allocation is done
d. All of the above
ANSWER: All of the above
40) Delay in handoffs is
caused due to
a. Week signal conditions
b. High traffic conditions
c. Un availability of the channel
d. All of the above
ANSWER: All of the above
41) Inter system Handoffs
are done
a. When mobile station moves in two
cellular systems with different MSC
b. When mobile station moves between two cellular
systems
c. When mobile station receives more power from
other base station than the serving base station
d. All of the above
ANSWER: All of the above
42) When a fraction of
assigned channel is reserved for handoffs, it is
a. Guard channel concept
b. Fixed channel assignment
c. Dynamic channel assignment
d. None of the above
ANSWER: Guard channel concept
43) While handoffs, the
termination of call may be avoided by
a. Providing Guard channel
b. Queuing of handoffs
c. Both a & b
d. None of the above
ANSWER: Both a & b
44) Dwell time is the
time for
a. A call within the cell
b. Hand off
c. Waiting for channel allocation
d. None of the above
ANSWER: A call within the cell
45) Dwell time depends
upon
a. Interference
b. Distance between the subscriber and the base
station
c. Propagation of call
d. All of the above
ANSWER: All of the above
46) In Mobile Assisted
Handoff (MAHO), the handoff takes place when
a. The power received by the mobile
station from other base station is more than the serving base station
b. The channel allocated is not available
c. The mobile station has no signal
d. All of the above
ANSWER: The power received by the mobile
station from other base station is more than the serving base station
47) Mobile Assisted
Handoff (MAHO) provides
a. Faster handoffs
b. Suitability for frequent handoffs
c. MSC need not monitor the signal strength
d. All of the above
ANSWER: All of the above
48) Trunking in a
cellular network refers to
a. Termination of a call
b. Spectrum unavailability
c. Accommodating large number of users in limited
spectrum
d. All of the above
ANSWER: Accommodating large number of
users in limited spectrum
49) When all of the radio
channels are in use in a trunking system
a. The user is blocked
b. The access to the system is denied
c. The queue may be provided
d. All of the above
ANSWER: All of the above
50) Umbrella cell
approach
a. Uses large and small cells
b. Uses different antenna heights
c. Is used for high speed users with large
coverage area and low speed users with small coverage area
d. All of the above
ANSWER: All of the above
51) Interference in
cellular systems is caused by
a. Two base stations operating in
same frequency band
b. Two calls in progress in nearby mobile stations
c. Leakage of energy signals by non cellular
systems into cellular frequency band
d. All of the above
ANSWER: All of the above
52) Interference in
frequency bands may lead to
a. Cross talk
b. Missed calls
c. Blocked calls
d. All of the above
ANSWER: All of the above
53) Co-channel reuse
ratio depends upon
a. Radius of the cell
b. Distance between the centers of the co channel
cells
c. Frequency allocation of nearest cells
d. Both a and b
e. Both b and c
ANSWER: Both a and b
14) Increase in Co-
channel reuse ratio indicates
a. Better transmission quality
b. Larger capacity
c. Low co-channel interference
d. Both a and c
e. Both a and b
ANSWER: Both a and c
55) Grade of service
refers to
a. Accommodating large number of
users in limited spectrum
b. Ability of a user to access trunked system
during busy hour
c. Two calls in progress in nearby mobile stations
d. High speed users with large coverage area
ANSWER: Ability of a user to access
trunked system during busy hour
56) Traffic intensity is
expressed in
a. Erlangs /MHz /km2
b. Erlangs
c. λ/ sec
d. dB/sec
ANSWER: Erlangs
57) The techniques used
to improve the capacity of cellular systems are
a. Splitting
b. Sectoring
c. Coverage zone approach
d. All of the above
ANSWER: All of the above
58) Distributed antenna
systems are used at
a. Transmitters of mobile systems
b. Transmitters of base stations
c. Inputs and outputs of repeaters
d. Receivers of mobile stations
ANSWER: Inputs and outputs of repeaters
59) Antenna down tilting
refers to
a. Focusing radio energy towards
ground
b. Decreasing the strength of antenna
c. Decreasing the S/N ratio at the antenna input
d. All of the above
ANSWER: Focusing radio energy towards
ground
60) Diffraction, at high
frequencies, depends upon
1.
Geometry of the object
2. Polarization of the incident wave
3. Amplitude of the incident wave
4. Frequency of the incident wave
a. 1 and 2 are correct
b. 1, 2 and 3 are correct
c. 2 and 3 are correct
d. All are correct
ANSWER: 1, 2 and 3 are correct
61) The rainbow pattern
seen on a CD is an example of
a. Reflection
b. Refraction
c. Diffraction
d. None of the above
ANSWER: Diffraction
62) Fresnel Reflection
Coefficient is a factor of
1.
Polarization of the wave
2. Properties of the material at which reflection occurs
3. Angle of incidence of wave
a. 1 and 2 are correct
b. 1 and 3 are correct
c. All the three are correct
d. 2 and 3 are correct
ANSWER: All the three are correct
63) When a wave falls on
a perfect conductor
a. Wave is partially reflected and
partially transmitted
b. All incident energy is reflected back without
loss of energy
c. Part of energy gets absorbed
d. Both a and c
ANSWER: All incident energy is reflected
back without loss of energy
64) Brewster angle is the
angle at which
a. No reflection occurs at the first
medium
b. Reflection coefficient is zero
c. The wave gets refracted in the direction of
source
d. Both a and b
e. Both a and c
ANSWER: Both a and b
65) Fading is caused due
to
1.
Multi path propagation
2. Obstacles
3. Frequency variations at the source
4. Variation in amplitude and phase at receiver
a. 1 and 2 are correct
b. 1, 2 and 4 are correct
c. 2 and 3 are correct
d. All are correct
ANSWER: 1, 2 and 4 are correct
66) Coherence time refers
to
a. Time required to attain a call
with the busy base station
b. Time required for synchronization between the
transmitter and the receiver
c. Minimum time for change in magnitude and phase
of the channel
d. None of the above
ANSWER: Minimum time for change in
magnitude and phase of the channel
67) Fading due to shadowing
is
a. Fading due to large obstructions
b. Large coherence time of the channel as compared
to the delay constraints
c. Small coherence time of the channel as compared
to the delay constraints
d. Both a and b
e. Both a and c
ANSWER: Both a and b
68) Deep fade is
1.
Strong destructive interference
2. Drop in signal to noise ratio
3. Temporary failure of message transfer
a. 1 and 2 are correct
b. 1 and 3 are correct
c. 2 and 3 are correct
d. All are correct
ANSWER: All are correct
69) Doppler spread refers
to
a. Signal fading due to Doppler shift
in the channel
b. Temporary failure of message transfer
c. Large coherence time of the channel as compared
to the delay constraints
d. All of the above
ANSWER: Signal fading due to Doppler shift
in the channel
70) Friis free space
equation
1.
Is an expression for noise power
2. Is a function of transmitting and receiving antenna gain
3. Depends upon the distance between transmitting and receiving antenna
a. 1 and 2 are correct
b. 1 and 3 are correct
c. 2 and 3 are correct
d. All are correct
ANSWER: 2 and 3 are correct
71) The free space model
of propagation refers to
1.
Unobstructed line of sight between the transmitter and receiver
2. Satellite communication systems and Microwave line of sight radio links
3. Propagation along the ground surface
a. 1 and 2 are correct
b. 1 and 3 are correct
c. 2 and 3 are correct
d. All the three are correct
ANSWER: 1 and 2 are correct
72) According to Friis
free space equation
1.
Received power falls with square of the distance between the transmitter and
receiver
2. Increases with square of the distance between the transmitter and receiver
3. Received power increases with gains of transmitting and receiving antennas
a. 1 and 2 are correct
b. 1 and 3 are correct
c. All the three are correct
d. 2 and 3 are correct
ANSWER: All the three are correct
73) EIRP is
1.
Effective Isotropic Radiated Power
2. Maximum radiated power available by the transmitter
3. A factor of power and gain of transmitter
a. 1 and 2 are correct
b. 1 and 3 are correct
c. All the three are correct
d. 2 and 3 are correct
ANSWER: All the three are correct
74) Spread spectrum
modulation involves
1.
PN sequence for modulation
2. Large bandwidth
3. Multiple users
a. 1 and 2 are correct
b. 1 and 3 are correct
c. 2 and 3 are correct
d. All the three are correct
ANSWER: All the three are correct
75) PN sequence at the
decoder acts as a locally generated carrier at the receiver and decodes the
signal using
a. Correlator
b. Adder
c. Frequency divider
d. PLL
ANSWER: Correlator
76) In spread spectrum
technique, the multiple users are assigned with
a. Same spectrum and same PN code
b. Same spectrum and different PN code
c. Different spectrum and different PN code
d. Different spectrum and same PN code
ANSWER: Same spectrum and different PN
code
77) Advantage of using
Spread Spectrum modulation is/are
1.
Interference rejection capability
2. Frequency planning is not required
3. Resistance to multipath fading
4. ISI is lesser
a. 1 and 2 are correct
b. 1, 2 and 3 are correct
c. 2 and 3 are correct
d. All the four are correct
ANSWER: All the four are correct
78) Direct sequence
spread spectrum demodulation uses
a. DPSK
b. FSK
c. ASK
d. QPSK
ANSWER: DPSK
79) Fast hopping is
a. More than one frequency hop during
each symbol
b. Hopping rate greater than or equal to
information symbol rate
c. One or more symbols transmitted between
frequency hops
d. Both a and b
e. Both b and c
ANSWER: Both a and b
80) Slow frequency
hopping refers to
a. One or more symbols transmitted in
time interval between frequency hops
b. More than one frequency hop during each symbol
c. Hopping rate greater than or equal to
information symbol rate
d. Both a and c are correct
ANSWER: One or more symbols transmitted in
time interval between frequency hops
81) Probability of outage
refers to
a. Noise developed at the receiver
b. Number of bit errors during transmission
c. Signal to noise ratio
d. All of the above
ANSWER: Number of bit errors during
transmission
82) The digital
modulation technique used in frequency selective channels is
a. FSK
b. ASK
c. BPSK
d. QPSK
ANSWER: BPSK
83) Working of Adaptive
Equalizers include
a. Training
b. Tracking
c. Modulation
d. Both a and b
e. All a, b and c are correct
ANSWER: Both a and b
84) The time span for
which the equalizer converges depends upon
1.
Equalizer algorithm
2. Equalizer structure
3. Rate of change of multipath radio channel
4. Amplitude of signal
a. 1 and 2 are correct
b. 1, 2 and 3 are correct
c. 2 and 3 are correct
d. All the four are correct
ANSWER: 1, 2 and 3 are correct
85) The Linear Equalizer
may be implemented as
a. FIR filter
b. Lattice filter
c. Low pass filter
d. Both a and b
e. Both a and c
ANSWER: Both a and b
86) Linear equalizer is
also known as
a. Transversal filter
b. Lattice filter
c. Low pass filter
d. None of the above
ANSWER: Transversal filter
87) The methods used for
non linear equalization are
a.
Decision Feedback Equalization
b. Maximum Likelihood Symbol Detection
c. Maximum Likelihood Sequence Estimation
a. 1 and 2 are correct
b. 1, 2 and 3 are correct
c. 2 and 3 are correct
d. None of the above
ANSWER: 1, 2 and 3 are correct
88) The performance of
algorithms for Adaptive Equalization are given by
1.
Rate of convergence
2. Computational complexity
3. Numerical properties
4. Frequency change
a. 1 and 2 are correct
b. 1, 2 and 3 are correct
c. 2 and 3 are correct
d. All are correct
ANSWER: 1, 2 and 3 are correct
89) Computational
complexity of an algorithm refers to the
a. Number of operations for one
iteration of algorithm
b. Inaccuracies in the mathematical analysis
c. Noise produced during one complete iteration of
algorithm
d. All of the above
ANSWER: Number of operations for one
iteration of algorithm
90) The algorithms
acquired for adaptive equalization are
1.
Zero forcing algorithm
2. Least mean squares algorithm
3. Recursive least squares algorithm
a. 1 and 2 are correct
b. 1, 2 and 3 are correct
c. 2 and 3 are correct
d. None of the above
ANSWER: 1, 2 and 3 are correct
91) Fractionally spaced
equalizer acts as
a. Matched filter
b. Equalizer
c. Demodulator
d. Both a and b
e. All a, b and c are correct
ANSWER: Both a and b
92) Diversity employs the
decision making at
a. Transmitter
b. Receiver
c. Transmitter and receiver
d. Communication channel
ANSWER: Receiver
93) The diversity schemes
are based on
1.
Time diversity
2. Frequency diversity
3. Space diversity
4. Polarization diversity
a. 1 and 2 are correct
b. 1, 2 and 3 are correct
c. 2 and 3 are correct
d. All the four are correct
ANSWER: All the four are correct
94) In time diversity
a. Multiple versions of signals are
transmitted at different time instants
b. The signal is transmitted using multiple
channels
c. Signal is transmitted with different
polarization
d. All of the above
ANSWER: Multiple versions of signals are
transmitted at different time instants
95) RAKE receiver is
1.
Several sub receivers
2. Several correlators
3. Fingers
4. Equalization based
a. 1 and 2 are correct
b. 1, 2 and 3 are correct
c. 2 and 3 are correct
d. All the four are correct
ANSWER: 1, 2 and 3 are correct
96) The RAKE receiver
involves the steps
a. Correlator, estimation of transmitted
signal, demodulation, bit decision
b. Estimation of transmitted signal, correlator,
demodulation, bit decision
c. Estimation of transmitted signal, demodulation,
correlator, bit decision
d. Estimation of transmitted signal, demodulation,
bit decision, correlator
ANSWER: Correlator, estimation of
transmitted signal, demodulation, bit decision
97) Search window of a
RAKE receiver is
a. Frequency band of the channel
b. Range of the time delays
c. Range of noise
d. All of the above
ANSWER: Range of the time delays
98) Speech Coders are
categorized on the basis of
a. Signal compression techniques
b. Frequency of signal
c. Bandwidth of the signal
d. All of the above
ANSWER: Signal compression techniques
99) Waveform coders and
Vocoders are the types of
a. Speech coders
b. Modulation technique
c. Frequency translation methods
d. Channel allocation for transmission
ANSWER: Speech coders
100) PCM, DPCM, DM, ADPCM
are the types of
a. Vocoders
b. Waveform coders
c. Channel allocation for transmission
d. All of the above
ANSWER: Waveform coders
101) Speech coding
technique that is independent of the source is
a. Vocoders
b. Waveform coders
c. Both a & b
d. None of the above
ANSWER: Waveform coders
102) Advantage of using
waveform coders is
1.
Independent of the signal source
2. Less complexity
3. Suitable for noisy environments
a. 1 and 2 are correct
b. 1 and 3 are correct
c. 2 and 3 are correct
d. All the three are correct
ANSWER: All the three are correct
103) The type of
frequency domain coding that divides the speech signal into sub bands is
a. Waveform coding
b. Vocoders
c. Block transform coding
d. Sub-band coding
ANSWER: Sub-band coding
104) The speech coding
technique that is dependent on the prior knowledge of the signal is
a. Waveform coders
b. Vocoders
c. Sub band coding
d. Block transform coding
ANSWER: Vocoders
105) The steps involved
in Channel vocoders for speech transmission are
a. Envelope detection, sampling,
encoding, multiplexing
b. Sampling, Envelope detection, encoding,
multiplexing
c. Envelope detection, encoding, sampling,
multiplexing
d. Sampling, Envelope detection, multiplexing,
encoding
ANSWER: Envelope detection, sampling,
encoding, multiplexing
106) Vocal tract cepstral
coefficients and excitation coefficients are separated by
a. Samplers
b. Linear filters
c. Encoders
d. Multiplexers
ANSWER: Linear filters
107) In voice excited
vocoders, PCM transmission helps in transmission of
a. High frequency bands of speech
b. Low frequency bands of speech
c. Multiplexed signals
d. Modulated signals
ANSWER: Low frequency bands of speech
108) Linear predictive
coders are based on the principle that
1.
Current signal sample is obtained from linear combination of past samples
2. Current signal sample is independent of past samples
3. These are time domain vocoders
4. They are among low bit rate vocoders
a. 1, 3 and 4 are correct
b. 2, 3 and 4 are correct
c. 1 and 4 are correct
d. All the four are correct
ANSWER: 1, 3 and 4 are correct
109) Multi pulse excited
LPC includes
1.
Multiple pulses per period
2. Minimization of weighted mean square error
3. Better speech quality
4. Pitch detection is not required
a. 1 and 4 are correct
b. 1 and 3 are correct
c. 2 and 4 are correct
d. All four are correct
ANSWER: All four are correct
110) In residual excited
LPC,
a. The residue of subtraction of
generated and original signal is quantized at the transmitter
b. Pitch detection is not required
c. Multiple pulses per period
d. Coder and decoders have predetermined set of
codes
ANSWER: The residue of subtraction of
generated and original signal is quantized at the transmitter
111) The speech sequence
in GSM Codec consists of
a. Pre emphasis, segmentation,
windowing, filtering
b. Windowing, Pre emphasis, segmentation,
filtering
c. Pre emphasis, windowing, segmentation, filtering
d. Pre emphasis, segmentation, filtering,
windowing
ANSWER: Pre emphasis, segmentation,
windowing, filtering
112) The windowing
technique used for speech coding in GSM Codec is
a. Blackman window
b. Welch window
c. Cosine window
d. Hamming window
ANSWER: Hamming window
113) The received signal
at the GSM speech decoder is passed through
a. STP filter
b. LTP filter
c. Quantizer
d. PLL
ANSWER: LTP filter
114) In GSM Codec, the
bits encoded for forward error correction are
a. Ia bits
b. Ib bits
c. II bits
d. Both a and b
e. Both a and c
ANSWER: Both a and b
115) The speech coders
are selected on the basis of
1.
Robustness to transmission errors
2. Cell size
3. Type of modulation technique used
4. Distance between the transmitter and receiver
a. 1 and 4 are correct
b. 1, 2 and 3 are correct
c. 2 and 4 are correct
d. All four are correct
ANSWER: 1, 2 and 3 are correct
116) FDMA is the division
of
a. Time
b. Phase
c. Spectrum
d. Amplitude
ANSWER: Spectrum
117) Guard band is
a. The small unused bandwidth between
the frequency channels to avoid interference
b. The bandwidth allotted to the signal
c. The channel spectrum
d. The spectrum acquired by the noise between the
signal
ANSWER: The small unused bandwidth between
the frequency channels to avoid interference
118) Cable television is
an example of
a. TDMA
b. FDMA
c. CDMA
d. SDMA
ANSWER: FDMA
119) In FDMA,
1.
Each user is assigned unique frequency slots
2. Demand assignment is possible
3. Fixed assignment is possible
4. It is vulnerable to timing problems
a. 1 and 2 are correct
b. 2 and 4 are correct
c. 1, 2 and 3 are correct
d. All four are correct
ANSWER: 1, 2 and 3 are correct
120) FDMA demand
assignment uses
1.
Single channel per carrier
2. Multi channel per carrier
3. Single transmission in one time slot
4. Multi transmission in one time slot
a. 1 and 2 are correct
b. 2, 3 and 4 are correct
c. 1, 2 and 3 are correct
d. All four are correct
ANSWER: 1 and 2 are correct
121) The advantages of
FDMA over TDMA includes
1.
Division is simpler
2. Propagation delays are eliminated
3. Cheaper filters with less complicated logic functions
4. Linearity
a. 1, 2 and 3 are correct
b. 1 and 2 are correct
c. 1 and 4 are correct
d. All four are correct
ANSWER: 1 and 2 are correct
122) TDMA is a multiple
access technique that has
a. Different users in different time
slots
b. Each user is assigned unique frequency slots
c. Each user is assigned a unique code sequence
d. Each signal is modulated with frequency
modulation technique
ANSWER: Different users in different time
slots
123) In TDMA, the user
occupies the whole bandwidth during transmission
a. True
b. False
ANSWER: True
124) TDMA allows the user
to have
a. Use of same frequency channel for
same time slot
b. Use of same frequency channel for different
time slot
c. Use of same time slot for different frequency
channel
d. Use of different time slot for different
frequency channels
ANSWER: Use of same frequency channel for
different time slot
125) GSM is an example of
a. TDMA cellular systems
b. FDMA cellular systems
c. CDMA cellular systems
d. SDMA cellular systems
ANSWER: TDMA cellular systems
126) TDMA is employed
with a TDMA frame that has preamble. The preamble contains Address of base
station and subscribers
1.
Synchronization information
2. Frequency allotted
3. Coded sequence
a. 1 and 2 are correct
b. 1, 2 and 3 are correct
c. 2 and 4 are correct
d. All four are correct
ANSWER: 1 and 2 are correct
127) CDMA is
1.
Spread spectrum technology
2. Using same communication medium
3. Every user stays at a certain narrowband channel at a specific time period
4. Each user has unique PN code
a. 1, 2 and 3 are correct
b. 2 and 3 are correct
c. 1, 2 and 4 are correct
d. All four are correct
ANSWER: 1, 2 and 4 are correct
128) Global Positioning
System uses
a. CDMA
b. TDMA
c. SDMA
d. FDMA
ANSWER: CDMA
129) CDMA is advantageous
over other Spread Spectrum techniques for
1.
The privacy due to unique codes
2. It rejects narrow band interference
3. Resistance to multi path fading
4. Its ability to frequency reuse
a. 1, 2 and 3 are correct
b. 2 and 3 are correct
c. 1, 2 and 4 are correct
d. All the four are correct
ANSWER: All the four are correct
130) The wide band usage
in CDMA helps in
1.
Increased immunity to interference
2. Increased immunity to jamming
3. Multiple user access
4. Different spectrum allocation in different time slots
a. 1, 2 and 3 are correct
b. 2, 3 and 4 are correct
c. 1, 2 and 4 are correct
d. All the four are correct
ANSWER: 1, 2 and 3 are correct
131) The advantages of
using a CDMA technique over other spread spectrum techniques are
1.
Increased capacity
2. Easier handoff
3. Better measure of security
4. Multiple users occupy different spectrum at a time
a. 1, 2 and 3 are correct
b. 2, 3 and 4 are correct
c. 1, 2 and 4 are correct
d. All the four are correct
ANSWER: 1, 2 and 3 are correct
132) FHMA is
1.
Spread spectrum technology
2. Using same communication medium
3. Every user has assigned unique frequency slot
4. Each user has unique PN code
a. 1 and 2 are correct
b. 1, 2 and 4 are correct
c. 2 and 4 are correct
d. All the four are correct
ANSWER: All the four are correct
133) OFDM is a technique
of
1.
Encoding digital data
2. Multiple carrier frequencies
3. Wide band digital communication
4. 4G mobile communication
a. 1, 2 and 3 are correct
b. 2 and 3 are correct
c. 1, 2 and 4 are correct
d. All the four are correct
ANSWER: All the four are correct
134) Advantages of using
OFDM include
1.
Avoids complex equalizers
2. Low symbol rate and guard interval
3. Avoids ISI
4. Multiple users at same frequency
a. 1, 2 and 3 are correct
b. 2 and 3 are correct
c. 1, 2 and 4 are correct
d. All the four are correct
ANSWER: All the four are correct
135) The troubles that
OFDM faces over other spread spectrum techniques are
1.
Sensitivity to Doppler shift
2. Frequency synchronization problems
3. Time synchronization problems
4. Low efficiency due to guard intervals
a. 1, 2 and 3 are correct
b. 2 and 3 are correct
c. 1, 2 and 4 are correct
d. All the four are correct
ANSWER: 1, 2 and 4 are correct
136) The guard interval
is provided in OFDM
a. To eliminate the need of pulse
shaping filter
b. To eliminate ISI
c. High symbol rate
d. Both a and b
e. Both b and c
ANSWER: Both a and b
137) Packet radio refers
to
a. Multiple users on single channel
b. Single user on multiple channels as per demand
c. Multiple users on multiple channels at
different time slots
d. Multiple users with coding techniques
ANSWER: Multiple users on single channel
138) Disadvantages of
packet radio are
a. Induced delays
b. Low spectral efficiency
c. Large spectrum required
d. Both a and b
e. Both b and c
ANSWER: Both a and b
139) Pure ALOHA is a
a. Random access protocol
b. Scheduled access protocol
c. Hybrid access protocol
d. Demand access protocol
ANSWER: Random access protocol
140) The increase in
number of users in PURE ALOHA causes
a. Increase in delay
b. Increase in probability of collision
c. Increase in spectrum
d. Both a and b
e. Both a and c
ANSWER: Both a and b
141) SDMA technique
employs
a. Smart antenna technology
b. Use of spatial locations of mobile units within
the cell
c. More battery consumption
d. Both a and b are correct
e. Both b and c are correct
ANSWER: Both a and b are correct
142) The advantage of
using SDMA over other spread spectrum technique is
a. Mobile station battery consumption
is low
b. Reduced spectral efficiency
c. Increased spectral efficiency
d. Both a and b are correct
e. Both a and c are correct
ANSWER: Both a and c are correct
143) The increased
capacity of SDMA is due to
a. Focused signal transmitted into
narrow transmission beams
b. Smart antennas pointing towards mobile stations
c. Use of different frequencies at same time slot
d. Both a and b are correct
e. Both a and c are correct
ANSWER: Both a and b are correct
144) Coherence time is
a. Directly proportional to Doppler
spread
b. Indirectly proportional to Doppler spread
c. Directly proportional to square of Doppler
spread
d. Directly proportional to twice of Doppler
spread
ANSWER: Directly proportional to Doppler
spread
145) Types of small scale
fading, based on Doppler spread are
a. Fast fading
b. Frequency non selective fading
c. Flat fading
d. Frequency selective fading
ANSWER: Fast fading
146) Flat fading or
frequency nonselective fading is a type of
a. Multipath delay spread small scale
fading
b. Doppler spread small scale fading
c. Both a & b
d. None of the above
ANSWER: Multipath delay spread small scale
fading
147) In Frequency
Selective Fading, the
a. Coherence Bandwidth of the channel
is less than bandwidth of transmitted channel
b. Coherence Bandwidth of the channel is more than
bandwidth of transmitted channel
c. Coherence Bandwidth of the channel is equal to
bandwidth of transmitted channel
d. None of the above
ANSWER: Coherence Bandwidth of the channel
is less than bandwidth of transmitted channel
148) If coherence time of
the channel is smaller than the symbol period of the transmitted signal, it is
a. Fast fading
b. Slow fading
c. Frequency selective fading
d. Frequency non selective fading
ANSWER: Fast fading
149) The power delay
profile helps in determining
a. Excess delay
b. rms delay spread
c. Excess delay spread
d. All of the above
ANSWER: All of the above
150) Coherence bandwidth
is
a. Channel that passes all spectral
components with equal gain
b. The bandwidth of modulated signal
c. Channel that passes all spectral components
with linear phase
d. Both a and c
e. Both a and b
ANSWER: Both a and c
151) Small scale
multipath propagation is caused due to waves with
1.
Different propagation delays
2. Different amplitudes
3. Different phase
a. 1 and 2 are correct
b. 1 and 3 are correct
c. 2 and 3 are correct
d. All the three are correct
ANSWER: All the three are correct
152) The effects of small
scale multipath propagation are
1.
Changes in signal strength
2. Random frequency modulation
3. Time dispersion
a. 1 and 2 are correct
b. 1 and 3 are correct
c. 2 and 3 are correct
d. All the three are correct
ANSWER: All the three are correct
153) Impulse response of
a multipath channel is determined by the fact that
a. Mobile radio channel may be
modeled as linear filter
b. Impulse response is time varying
c. Both a & b
d. None of the above
ANSWER: Both a & b
154) The received signal
from a multipath channel is expressed as
a. Convolution of transmitted signal
and impulse response
b. Addition of transmitted signal and impulse
response
c. Subtraction of transmitted signal and impulse
response
d. All of the above
e. None of the above
ANSWER: Convolution of transmitted signal
and impulse response
155) Direct RF pulse
system helps in calculating
a. Impulse response in frequency
domain
b. Impulse response in phase domain
c. Power delay of the channel
d. All of the above
ANSWER: Power delay of the channel
156) The techniques used
for small scale multipath measurements are
1.
Direct RF pulse system
2. Spread spectrum sliding correlator channel sounding
3. Frequency domain channel sounding
a. 1 and 2 are correct
b. 1 and 3 are correct
c. 2 and 3 are correct
d. All the three are correct
ANSWER: All the three are correct
0 Comments